Clear-com WTR-680 Manual do Utilizador

Op er ating In struc tionsWBS-680, WTR-680, WTR-682Pro fes sional Wire lessIn ter com Sys temRIntercom Systems

2-4 Blank

WTR-680 Beltpack Con trols and Con nec tions - Top PanelFig ure 4WTR-680 Top Panel1. On/Off & Vol ume Con trol – Turns the beltpack poweron an

Con trols and Con nec tions - Rear PanelFig ure 5WTR-680 Rear Panel/Con nec tor/An tennas1. [MENU] and [SET] but tons – Used to se lect menus an

3-3WTR-680Spec i fi ca tionsRF Fre quency Range ...518 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bandsPower Re quire ments...

3-4 Blank

WTR-682 Beltpack Con trols and Con nec tions - Top PanelFig ure 7WTR-682 Top Panel1. On/Off and Vol ume Con trol - Turns beltpack power onand con

Con trols and Con nec tions - Rear PanelFig ure 8 WTR-682 Rear Panel/Con nec tor/An tennas1. [MENU] and [SET] but tons – Used to se lect menus a

4-3WTR-682Spec i fi ca tionsRF Fre quency Range ...470 - 608 MHz, 614 - 746 MHz in 18 MHz TX and RX bandsPower Re quire ments...

4-4 Blank

Ini tial Equip ment Set-UpUn packingUn pack your Clear-Com Sys tem. Be low are the items thatshould come with your base sta tion and each belt pack.

Thank you for choos ing Clear-ComClear-Com In ter com Systems would like to take this op por tu nity to thank you for choos ing the Clear-ComWBS-680 P

An tenna Con nec tionThe base sta tion is sup plied with two (2) an ten nas. One1/2-wave an tenna for Trans mit and one 1/2-wave for Re ceive.The an

Keep the dis tance be tween the base sta tion and the beltpacksas short as pos si ble. The greater the dis tance, the weaker thesig nal. Make sure the

Fig ure 17An tenna Place mentImproving Re cep tion and In creasingRangeKeeping the dis tance from the base sta tion and beltpack asshort, and un ob

Base Sta tion Set-upLo ca tionLo cate the base sta tion with the front and rear of the unit ac --ces si ble so that switches may be set and con nec ti

In ter nal Trans mit SwitchesIn ter nal to the WBS-680 are two trans mit switches which en --able a user to turn on or off the two trans mit ters in

Dual Lis ten Func tion al ityThe base sta tion’s main au dio board has the op tion of plac ingad di tional parts to en able dual lis ten. Dual lis t

Aux il iary In put/Out putThe in put and out put 3-pin XLR aux il iary con nec tions are forsup ply ing ad di tional bal anced au dio into and

Stage An nounce / Re lay Con tacts The stage an nounce out put con nec tor is where au dio ex its thebase when any of the beltpacks press the [SA] but

Base Sta tion LinkThis RJ-45 type jack al lows the con nec tion of wire less talkaround (WTA) to two base sta tions. This al lows WTA on I/Cchan nel A

Beltpack Set-upBat tery In stal la tionEn sure that the On/Off vol ume con trol knob is turned off. Press down and hold down the bat tery re lease la

-i-Ta ble of Con tentsIn tro duc tion ...1-1Gen eral De scrip tion ...

An tenna Con nec tionThe beltpack co mes with two de tach able, screw-type,1/4-wave an ten nas. To at tach the two an ten nas, screw into there cep t

Pre-Walk-Thru Check listFol low ing the in struc tions fully to this point you have suc cess --fully com pleted the fol low ing check list:❒Lo cated t

6-2 Blank

System Op er a tionFre quency Plan Over viewThe WBS/WTR-680 has 36 fac tory-defined fre quency groupsand 12 user-programmable fre quency groups. A Gr

Base Sta tion Op er a tionPower If you have fol lowed the in struc tions in Sec tion 5, “Ini tialEquip ment Set-Up”, you should now be ready to turn

Dis play Con trastThe LCD’s (Liq uid Crys tal Dis play) con trast is set from thefac tory to a stan dard level. How ever it is pos si ble for the us

WBS-680 Menu Struc tureMain Screen FlowchartThe fol low ing con tains the base sta tion menu struc ture andref er ences the pages in which fur ther de

Power-Up Screen•This screen is dis played only on power up, first use de -fault, and fac tory de fault. •The 1st up per-right-corner num ber dis plays

Group / Chan nel Se lectThe Group/Chan nel se lect screen al lows the user to change the group and se lect from a pre-determined num ber of chan nelso

Group / Fre quency Se lectThe Group/Fre quency se lect screen al lows a user to set thegroup and se lect from a pre-determined num ber of fre quen cie

Ta ble of Con tents (con tin ued)WTR-680 Beltpack Op er a tion ...7-11Power/Lo cal Hea

Fre quency Edit(User-Programmed Groups Only)This menu only oc curs for user-programmable groups or when copy ing to a user-programable group. The Fre

ScanScan per forms a fre quency scan of the fac tory-defined and any set-up user-programmable groups in or der to find the groupwith the high est num

Spe cial Key Se quencesLock out•Press [UP]+[DOWN] for 3 sec onds to lock or un lock thebase sta tion. Pressing [MENU] will still func tion to viewscr

Beltpack Op er a tionPower / Lo cal Head set Vol umeTurn the beltpack power on by ro tat ing the knob CW. Ad justthe vol ume to the head set by ro ta

WTR-680 Menu Struc tureBeltpack Menu Struc ture7-12[MENU]S10001c6000103A 01Power-Up Screen - Pg. 7-13 Group/Channel Screen - Pg. 7-14 GP CH[MENU]704

WTR-680 Menu Struc turePower-Up Screens•The first screens dis played when the beltpack is pow eredup are the soft ware and chan nel map ver sion scree

WTR-680 Menu Struc tureGroup / Chan nel ScreenThe Group/Chan nel screen al lows the user to change thegroup and se lect from a pre-determined num ber

WTR-680 Menu Struc tureTrans mit ScreenThe Transmit screen al lows the user to set the beltpack trans --mit fre quency. Fac tory-defined groups will

WTR-680 Menu Struc tureRe ceive 1 ScreenThe Receive 1 screen al lows the user to set the beltpack re --ceive 1 fre quency. This cor re sponds to the b

WTR-680 Menu Struc tureRe ceive 2 ScreenThe Re ceive 2 screen al lows the user to set the beltpack re --ceive 2 fre quency. This cor re sponds to the

1-1Gen eral De scrip tionThe Clear-Com WBS-680 UHF Syn the sized Wire less in ter --com sys tems of fer the ul ti mate in re li able, high-performanc

WTR-680 Menu Struc tureScanScan per forms a fre quency scan of the fac tory-defined and any set-up user-programmable groups in or der to find the clea

WTR-680 Menu Struc tureStage An nounce En able/Dis able•Press and hold [SET] then press the [SA] but ton to showthe SA en able/dis able screen. The

WTR-680 Menu Struc tureAu dio Chan nel A or B Dis able/En able•Press and hold [SET] then press the [CHAN] but ton toshow the chan nel en able/dis able

WTR-680 Menu Struc tureSpe cial Key Se quencesLock out•Press [UP]+[DOWN] for 3 sec onds to lock or un lock thebeltpack. The words “Loc on” will be dis

WTR-682 Menu Struc tureBeltpack Menu Struc ture7-22[MENU]S30001c6000103A 01Power-Up Screen - Pg. 7-23 Group/Channel Screen - Pg. 7-24 GP CH[MENU]704

WTR-682 Menu Struc turePower-Up Screens•The first screens dis played when the beltpack is pow eredup are the soft ware and chan nel map ver sion scree

WTR-682 Menu Struc tureGroup / Chan nel ScreenThe Group/Chan nel screen al lows the user to change thegroup and se lect from a pre-determined num ber

WTR-682 Menu Struc tureTrans mit ScreenThe Transmit screen al lows the user to set the beltpack trans --mit fre quency. Fac tory-defined groups will

WTR-682 Menu Struc tureRe ceive 1 ScreenThe Receive 1 screen al lows the user to set the beltpack re --ceive 1 fre quency. This cor re sponds to the b

WTR-682 Menu Struc tureRe ceive 2 ScreenThe Re ceive 2 screen al lows the user to set the beltpack re --ceive 2 fre quency. This cor re sponds to the

1-2margaiD kcolB 086-SBW

WTR-682 Menu Struc tureAu dio OutputThe Au dio Out put screen al lows the user to set the au dioout-put to Mono (Add) or Ste reo (SEP). This op tion

WTR-682 Menu Struc tureScanScan per forms a fre quency scan of the fac tory-defined and any set-up user-programmable groups in or der to find the clea

WTR-682 Menu Struc tureStage An nounce En able/Disable•Press and hold [SET] then press the [SA] but ton to showthe SA en able/dis able screen. The cur

WTR-682 Menu Struc tureWire less Talk Around•Press and hold [SET] then press the [WTA] but ton toshow the WTA menu screen. The cur rent set ting of th

WTR-682 Menu Struc tureAu dio Chan nel A Options•Press and hold [SET] then press the [A] but ton to showthe chan nel "A" menu screen. The cu

WTR-682 Menu Struc tureAu dio Chan nel B Op tions•Press and hold [SET] then press the [B] but ton to showthe chan nel "B" menu screen. The c

WTR-682 Menu Struc tureSpe cial Key Se quencesLock out•Press [UP]+[DOWN] for 3 sec onds to lock or un lock the beltpack. The words “Loc on” will be di

Sys tem Walk-ThruNow that you have suc cess fully “set-up” your Wire less In ter --com Sys tem and turned on any aux il iary

8-2 Blank

Trou ble shootingRe read the sec tions of this man ual to make sure you havecom pleted sys tem set-up prop erly.If you are un able to solve the prob l

WBS-680 Base Sta tionCon trols and Con nec tions - Front Panel1. Power switch.2. [Menu] and [Set] but tons – Used to se lect menus and setop tions on

9-2 Blank

Tech TipsFre quency In ter ac tionUn for tu nately, ra dio fre quency (RF) chan nels can not be ran --domly se lected for use in ra dio de vic

10-2 Blank

Bat tery In for ma tionIm proper bat tery se lec tion, use, in stal la tion and care are thecause of nu mer ous wire less sys tem fail ures.Al ka lin

11-2 Blank

In ter com Sys tems Spec i fi ca tions12-1Section12RTSIn put Im ped ance: ...200WOut put

12-2 Blank

Ac ces sories and Re place ment Parts 13-1Section13Base Sta tion’s AN-680 ½ - Wave An tenna Beltpack’s

13-2 Blank

14-1Section14Fac tory Ser viceAll equip ment re turned for re pair must be ac com pa nied by doc u men ta tion stat ing the re turn ad dress,tele pho

Con trols and Con nec tions - Rear Panel1. Re ceive An tenna - Fe male “TNC” Con nec tor. Color band on an tenna must match color dot on base sta tio

14-2 Blank

Cer tif i ca tion In for ma tion15-1Section15FCC LI CENSINGThe Clear-Com WBS-680 and the WTR-680 Trans mit ter/Re ceiver are Type Ac cepted un der Un

15-2 Blank

16-1Clear-Com Limited WarrantyThis prod uct is guar an teed by Clear-Com In ter com Sys tems to be free of man u fac tur ing de fects in ma te rial an

16-2 Blank

Clear-Com In ter com Sys tems 4065 Hollis Street, Emeryville, CA 94608-3505 PN 803541Rev B FEB 2003 Made in U.S.A.•RIntercom Systems

2-3WBS-680Spec i fi ca tionsOver allRF Fre quency Range ......518 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bandsPower Re quire me